Beginning Woodworking
Essential Tools for Beginners

Beginning woodworking does not require all of the tools in the world. But you need some. It is tough to have too many tools. As you gain experience, you develop an appreciation of the right tool for the job. That tool will make any task safer, easier, and quicker. However, in getting started in woodworking you need to have essential tools that help in most beginning projects.

Beginning woodworking concentrates on a good quality assortment of essential tools for beginners. Most beginners already own a few tools, such as a tape measure an assortment of screwdrivers , a hammer, and an extension cord. As you learned in the first few pages of Woodworking for Beginners, safety items such as goggles, ear muffs, and a dust mask are critical.
For beginning woodworking, it is a good idea to have a versatile workbench with a vise, as well.

The following provides a brief description of the essential tools and where to purchase a quality one.
Remember, it is always better to buy a quality woodworking tool rather than a cheap one. Normally, cheap tools have a shorter life, are less accurate and more dangerous to use.

Beginning Woodworking Tools

Contractor Saw

The contractor table saw is not as powerful as a cabinet saw, but they are okay for a beginner. They are very portable and offer decent productivity. This is beneficial for beginning woodworking in a garage or small area. These smaller woodworking table saws are good cutting plywood or ripping 2x4's.

I started out with a Delta Contractor Saw. It was okay. It lacked a precise fence, dust collection capabilities, and was underpowered. It is a good idea to find a more precise fence for a contractor saw.

You could try a Circular Saw & Guide to cut sheet goods down to size. But it will not do everything that you may need.

As you gain experience, you might want to update to a cabinet saw for power and accuracy. It is prudent to look at 3HP or above. An enclosed cabinet is adaptable for first-rate dust collection. A precision fence is important for a serious woodworker.

To find a good price on a quality table saw, please check Table Saws & Accessories

Beginning Woodworking Tools

Squares and Straight Edges

For beginning woodworking a couple of machinist squares are important. Make sure they are accurate. Holding back on this tool is a mistake. You'll use them for checking your work for square, drawing 90-degree lines, and setup chores.

Frequently, a combination square is necessary. Most have a 45-degree angle as well. I am keen on the Starrett Combination square for precision and versatility. I purchased a cheap one from a Discount Catalog and threw it away. Don't make that mistake.

Woodworking Tools

A Straight Edge is imperative for superior work. A straight edge helps you check cupped boards, makes sure the edge is square, and line up the router bit for jointing. I prefer the Starrett 24" Straight-edge, because it is precise.

For good pricing on Squares and Combination Squares, please visit Hand Tools page.

Woodworking Tools


A chisel is an important cutting tool. Chisels have a variety of uses. They can round the corners of tenons, remove glue in tight places, square up boards, used as a scraper, and many other things. I like chisels ranging in size from 1/4" to 1". It behooves you to get quality ones – you won't be sorry!

I've been using Marples Blue Chip Chisels for years. They are made in Sheffield England, and rarely need sharpening. If your tools need sharpening, the Veritas Sharpening System really works!

For good pricing on Chisels, see the Hand Tools page.

Woodworking Tools

Random Orbital Sander

Sanding is necessary in the finishing procedure for nearly any of your projects. Sanding may not be your favorite part of woodworking, but you can make it easier on yourself.

I have tried Belt Sanders, mini-Sanders, and Palm Sanders. All leave gouges and scratches. Your final finish does not need scratches. As you would guess, an ROS uses a random orbit to sand. This motion is what allows the smooth finish.

However, there is a difference in Random Orbital Sanders. You want a well-balanced sander that is is comfortable when you use it. Feel any vibrations as you turn on the sander. With excessive vibration, any sander causes fatigue, especially on large sanding projects.
For beginning woodworking, you only need a few grits of Sandpaper, such as 120 and 220 grits. These will handle nearly all of you finish work.

Please visit the Random Orbital Sander page for more information on a quality ROS.
To find discount prices on top quality Random Orbital Sanders, go to Random Orbital Sanders page.

Beginning Woodworking Tools

Sharpening System

Woodworking Truth #2 states "Learn to Sharpen". Have you ever used dull tools? You must know that they don't work very well, and there are a few that will not work at all. In beginning woodworking, this forces you into awkward and difficult habits. A necessary skill for woodworking is knowing how to sharpen. Better results come from sharp tools, and they are safer.

Along with a honing guide and angle jig, a good sharpening system needs water stones. The Norton Combination Water Stones are perfect for sharpening. I like the ones with different grits on each side. You can store the water stones in a Tupperware container, so that they are ready to use.

Beginning Woodworking Tools


You need clamps to hold joints tight while the glue dries. Most woodworkers assert that they never have sufficient clamps. There are a variety of clamps on the market, but you will do better by buying quality clamps.

C-clamps are okay, but they are annoying with the time it takes to open and/or close. In addition, C-clamps have inadequate reach. After I tried the Bessey sliding clamp (middle of picture), the C-clamps get limited use.

Some of the other woodworking clamps do not live up to their propaganda. When you are gluing up a project, normally you want the parts square. For beginning woodworking, you might as well get quality clamps that will serve you over a long period of time. The Bessey K-Body has newer versions on the market. And they are hard to beat. I suggest that you pick up a couple of 24" and 40" sizes.

Beginning Woodworking Tools

Please visit Woodworking Clamps for more information.
Frequently you can find some good pricing on the Bessey Clamps Woodworking page.

Drill and Drill Bits

Beginning Woodworking Tools

Frequently, you need to bore holes in wood. You can bore precise holes with a Drill Press. This tool allows you to drill correctly spaced holes and you can bore to exact depths. You can even use a drill press as a spindle sander. A drill press is a good choice because of its usefulness and fairly low cost.

Or you can use a hand drill. Electric hand drills come in corded or cordless versions. Both come in different sizes, such 1/4", 3/8" or 1/2", which equates to the maximum drill bit size. For beginning woodworking the 3/8" size is the best compromise. I like the cordless version for ease of use when you are not near an outlet. And the reversible variable speed allows you to use it for drilling or installing/extracting screws.
Sometimes you may need a right-angle drill, and several manufacturers sell hand drill kits with a T-Handle drill and a Right-Angle drill.

Any woodworker needs a set of countersinks to use with any drill. This allows you to recess screw heads, which is very handy.

Please visit Drill Press for good pricing on quality Drill Presses.
Or you can find some good buys on Electric Hand Drills.

Beginning Woodworking Tools

Combination Rasp/File

A versatile woodworking tool with a file section and a rasp section. This tool is great when working with wood or metal. One side is Flat and the other side is Half Round. Both sides have a Rasp Section and File Section.
The Nicholson 4-in-1 Hand Rasp & File, 10" Long, makes easy work for many woodworking projects.

You should be cautious, since rasps cut wood aggressively. The file sections are used to make the wood smooth. The combination rasp/file can rapidly profile either simple or complex projects.

Beginning Woodworking Tools

Bench Planes

A quality bench plane is another useful beginning woodworking tool. You use the bench plane to square and straighten up wood edges or to level the surface of a glued panel. Occasionally you may tear out wood grain. If this happens, just use the plane in the opposite direction.

If you have Quality Jigs, the hand plane sees limited use. However, they are nice to take a little wood off after glue-up.
If you decide to spend some money on a hand plane, be sure to get a good one. My Record #4 Bench Plane is very sharp. You can adjust it to cut a sliver. A good Bench plane should survive your lifetime.

I Trust That Beginning Woodworking on Tools Will Help You!


What is this?
Add to My Yahoo!
Add to My MSN
Add to Google

Return to Top  |   Home |
Best Place to Buy | Woodworking Jigs | Woodworking Plans | Wordworking Router | Patterns & Templates |
Machinery & Equipment | Table Saw Safety | Woodworking Shop | Woodworking Supplies | Woodworking Hand Tools |
Woodworking Finishing | Woodworking Joints | Project Gallery | Woodworking Ideas | Woodworking Truth |
Beginner's Guide | Woodworking Tradeshow | Your Projects | Buy - Sell Equipment |
Proven Blog | Support This Site | Site Map | Privacy Policy

Copyright © 2007 - 2010 - - All Rights Reserved
No Reproduction Permitted without Permission.